EN 9053 Digital Position Indicators Technopolymer Plastic, Electronic, 6 Digit LCD-Display

Photo

EN 9053 Technopolymer Plastic Digital Position Indicators, Electronic, 6 Digit LCD-Display Color: OR - Orange, RAL 2004
ELESA original design
code: DD52R-E
Color: OR - Orange, RAL 2004
EN 9053 Technopolymer Plastic Digital Position Indicators, Electronic, 6 Digit LCD-Display Color: OR - Orange, RAL 2004 EN 9053 Technopolymer Plastic Digital Position Indicators, Electronic, 6 Digit LCD-Display Color: GR - Gray, RAL 7035

Product description

Information

EN 9053 digital position indicators are extremely versatile in use, with virtually every counting option selectable directly at the device via the operating keys. The power necessary for the display is supplied by a long-life battery.

The indicators are assembled directly onto the spindle via their hollow shaft, with the torque limiting pin defining the position for the mounting site.

Mounted in this way, the indicators will detect the rotary spindle movement and show the appropriate value on the display.

Both housing sections are ultrasonically welded, making the housing extremely tight, stable and compact.

The foam rubber seal prevents the transmission of vibrations and also acts as a seal.



Specification

Housing
Plastic
Technopolymer (Polyamide PA)
Orange, RAL 2004OROR Color
Gray, RAL 7035GRGR Color
Temperature resistant up to 122 °F (50 °C)
Oil and solvent resistant

LCD display
6 digits and special characters

Hollow shaft
Stainless steel AISI 304

Seal
O-ring
Rubber NBR (Perbunan®)
(Only for identification no. 2)





RoHS compliant

On request

Housing
Plastic
Technopolymer (Polyamide PA)
Black-gray, RAL 7021SGSG Color

Technical drawing

3D
Hide technical drawing
EN 9053 Technopolymer Plastic Digital Position Indicators, Electronic, 6 Digit LCD-Display sketch

Part Options / Table

Identification no.

1Protection class IP 65
2Protection class IP 67

Build & Price

3D Product Configurator
Bore

Inch


Metric


Identification no.


Color
GR
OR

Installation Instructions

Montagehinweise GN 9053

Before installation of the position indicator, a bore hole for the torque limiting contact point is to be drilled, as shown in the in the adjacent drawing.

With the Mounting Adaptors EN 952.1 the hollow shaft (with bore 14 H7) of the position indicator can be adapted to fit the spindle.

If a reduction in the diameter of the hollow shaft is to be made at the same time as mounting a control knob, Control Knobs GN 957 are available which combine both functions in a single component (no adaptor bushings required).

The position indicator is mounted with the torque limiting contact point inserted in the bore hole, to stabilize the housing in place. The hollow shaft is mounted to the spindle and secured with the set screw.

With Clamping Plates GN 9053.6 spindles can be clamped and secured after adjusting.

Operating Principle

Electronic position indicators EN 9053 / EN 9054 / EN 9153 are very similar to mechanical position indicators EN 953 / EN 954 / EN 955 with regard to installation and external dimensions and can normally replace them.
The protection class IP 65 or IP 67 of the housing permits use in wet areas, even in contact with direct streams of water.
The measurement of the spindle rotations takes place directly, electronically and without contact. The required energy is supplied by a lithium battery with a lifespan of 5 or 8 years that can be easily replaced.
The special advantage of the electronic position indicator lies in its programmability. Nearly any desired counting option can be configured directly on the device using the function buttons.

Drawing Operating principle GN 9053 GN 9054

With 3 or 4 function buttons, it is possible to:
--Switch between incremental and absolute measurement modes
--Change the unit of measurement (mm, inches or degrees)
--Reset the counter or set an offset value
--Change the display after one rotation of the shaft and set the resolution, in other words, the number of decimal places displayed
--Set the direction of rotation / counting direction
--Adjustment for the display orientation (depending on the installation situation) and the maximum rotation speed

Selected Part

Total US Dollars (net)
$286.20
Call / Email for Delivery Time
Please note our quantity discounts (US Dollars).
MinMaxPrice
13$286.20
424$275.80
2549$260.19
≥ 50$234.17
Prop 65: -
Please contact our Sales Department for more information.
RoHS: -
No details on RoHS compatibility are available at this time. Please contact our Sales Department for more information.
Weight: 0.352 lbs
If weight is not listed, please contact our Sales Department for additional information regarding weight.
Phone: 800-877-8351
All Prices are in US Dollars. Taxes Not Included.

CAD Download

Other Data Formats

Email CAD File

To receive an email with a CAD download without creating an account, please enter your e-mail address. Max of 3 CAD files per day unless you create an account.

Please enter the code above.

CAD Download Tutorial About CAD Downloads
Save as Favorites

Please enter the code above.

Need Help?

Our service team is available from Monday to Friday between 7:30 AM and 5:00 PM Central Time: 800-877-8351

Special Requests | Contact our sales team

GN 9053-B3/4-1-GRGN 9053-B3/4-1-ORGN 9053-B3/4-2-GRGN 9053-B3/4-2-ORGN 9053-B20-1-GRGN 9053-B20-1-ORGN 9053-B20-2-GRGN 9053-B20-2-OR

This could also be interesting...

An error has occurred!
We have received your callback request and will contact you soon.
JW Winco Services

Our service team is available from Monday to Friday between 7:30 AM and 5:00 PM Central Time

Request Callback
Your Contact

You are looking for a Winco partner near you? Please select the country.