EN 541 Fluid Sight Glasses Crystal Clear Plastic

Fluid Sight Glasses EN 541: Crystal Clear Plastic

Original design
code: HFTX.

Type: A - With reflector

Plastic Characteristics

Product description

Fluid sight glasses EN 541 made of polyamide plastic have a high mechanical strength. Therefore, they can be produced with thinner walls and with a large viewing window.

These fluid sight glasses can also be used on pressurized tanks. Tests regarding maximum pressure are available.

Assembly note:
For wall thicknesses below 0.16 in (4 mm), use thin hex nuts GN 7430.

Specification

Body
Plastic
Crystal clear Polyamide PA-T
- Aging resistant
- High mechanical strength,
  but not alcohol resistant
- Temperature resistant 212 °F (100 °C)
- Solvent resistant,
  but not alcohol resistant

Reflector
Aluminum
Anodized finish, natural color

Seal
Rubber NBR (Perbunan^®)

RoHS

Accessory

Thin Hex Nuts GN 7430
Weld Bushings GN 7490 (Steel)

EN 541 Crystal Clear Plastic Fluid Sight Glasses sketch

Hide technical drawing

Part Options / Table

Type

A	With reflector
B	Without reflector

Part Number A - With reflector	Part Number B - Without reflector	d₁	d₂ Fine thread	Pipe thread	d₃	l₁	l₂	s	Recommended tightening torque in Nm


541-13-3/4X16-A	541-13-3/4X16-B	0.51	3/4 x 16	-	1.02	0.59	0.31	0.87	3
541-19-11/16X12-A	541-19-11/16X12-B	0.75	1 1/16 x 12	-	1.38	0.59	0.39	1.18	5
541-11-M16X1.5-A	541-11-M16X1.5-B	0.43	M 16 x 1.5	-	0.87	0.31	0.28	0.75	2...3
541-14-M20X1.5-A	541-14-M20X1.5-B	0.55	M 20 x 1.5	-	1.02	0.37	0.31	0.87	4...6
541-18-M25X1.5-A	541-18-M25X1.5-B	0.71	M 25 x 1.5	-	1.24	0.31	0.35	1.06	6...8
541-18-M26X1.5-A	541-18-M26X1.5-B	0.71	M 26 x 1.5	-	1.24	0.51	0.35	1.06	6...8
541-20-M27X1.5-A	541-20-M27X1.5-B	0.79	M 27 x 1.5	-	1.24	0.35	0.35	1.06	6...8
541-22-M30X1.5-A	541-22-M30X1.5-B	0.87	M 30 x 1.5	-	1.38	0.35	0.39	1.18	6...8
541-25-M35X1.5-A	541-25-M35X1.5-B	0.98	M 35 x 1.5	-	1.57	0.43	0.39	1.34	8...10
541-30-M40X1.5-A	541-30-M40X1.5-B	1.18	M 40 x 1.5	-	1.85	0.45	0.51	1.59	8...10
541-9-G1/4-A	541-9-G1/4-B	0.35	-	G 1/4	0.71	0.39	0.24	0.59	2...3
541-11-G3/8-A	541-11-G3/8-B	0.43	-	G 3/8	0.87	0.30	0.28	0.75	3...5
541-14-G1/2-A	541-14-G1/2-B	0.55	-	G 1/2	1.02	0.41	0.31	0.87	4...6
541-20-G3/4-A	541-20-G3/4-B	0.79	-	G 3/4	1.24	0.41	0.35	1.06	6...8
541-25-G1-A	541-25-G1-B	0.98	-	G 1	1.57	0.43	0.39	1.34	8...10
541-30-G11/4-A	541-30-G11/4-B	1.18	-	G 1 1/4	1.85	0.45	0.51	1.59	8...10

Show / Hide columns

Inch

Dimensions in: Inch (change to Metric)

d₁	d₂ Fine thread	Pipe thread	d₃	l₁	l₂	s	Recommended tightening torque in Nm

0.51	3/4 x 16	-	1.02	0.59	0.31	0.87	3
0.75	1 1/16 x 12	-	1.38	0.59	0.39	1.18	5

Show / Hide columns

Metric

Dimensions in: Inch (change to Metric)

d₁	d₂ Fine thread	Pipe thread	d₃	l₁	l₂	s	Recommended tightening torque in Nm

0.43	M 16 x 1.5	-	0.87	0.31	0.28	0.75	2...3
0.55	M 20 x 1.5	-	1.02	0.37	0.31	0.87	4...6
0.71	M 25 x 1.5	-	1.24	0.31	0.35	1.06	6...8
0.71	M 26 x 1.5	-	1.24	0.51	0.35	1.06	6...8
0.79	M 27 x 1.5	-	1.24	0.35	0.35	1.06	6...8
0.87	M 30 x 1.5	-	1.38	0.35	0.39	1.18	6...8
0.98	M 35 x 1.5	-	1.57	0.43	0.39	1.34	8...10
1.18	M 40 x 1.5	-	1.85	0.45	0.51	1.59	8...10
-	-	-	-	-	-	-	-
0.35	-	G 1/4	0.71	0.39	0.24	0.59	2...3
0.43	-	G 3/8	0.87	0.30	0.28	0.75	3...5
0.55	-	G 1/2	1.02	0.41	0.31	0.87	4...6
0.79	-	G 3/4	1.24	0.41	0.35	1.06	6...8
0.98	-	G 1	1.57	0.43	0.39	1.34	8...10
1.18	-	G 1 1/4	1.85	0.45	0.51	1.59	8...10