You are here: Product Overview > 3.7 Connecting, Assembling with Clamping and Connecting Elements > Mounting Accessories > GN 784 Swivel Ball Joint next product

GN 784 Swivel Ball Joint Aluminum

Photo

Type: A - Ball with internal thread
Identification no.: 1 - Clamping with adjustable lever

GN 784 Aluminum Swivel Ball Joint Type: A - Ball with internal thread
Identification no.: 2 - Clamping with set screw with hex socket

GN 784 Aluminum Swivel Ball Joint Type: B - Ball with external thread
Identification no.: 1 - Clamping with adjustable lever

GN 784 Aluminum Swivel Ball Joint Type: B - Ball with external thread
Identification no.: 2 - Clamping with set screw with hex socket

Standard Sheet GN 784 Print This Page Stainless Steel Characteristics

Product description

Information

Swivel ball joints GN 784 allow precise and stepless adjustment of the ball pivot within the swiveling range. This is a particular advantage when adjusting scanners, cameras, lighting, monitors, etc.

Thanks to the efficient clamping mechanism, only small amounts of torque on the clamping screw result in comparatively strong clamping forces on the ball. This force is easily applied with the adjustable lever (Identification no.1). When adjusting, the clamping must be completely released.

The ball joint can be mounted from below with the d₅ internal thread or together with the GN 784.1 flange, available as an accessory, using three through-holes from above.

For a permanent high stop torque, the contact surfaces of the balls must be kept free of grease. Exceeding the recommended tightening torques increases the stop torque, but may result in increased wear of the clamping mechanism.

Specification

Housing
Aluminum
Anodized finish, blackELS

Base plate / ball
Aluminum, plain finish

Adjustable lever
(Identification no. 1)

Zinc die-cast
Powder coated
Silver, RAL 9006, textured finish
Threaded stud and retaining screw
Stainless steel AISI 303

Set screw (Identification no. 2)
Stainless steel AISI 304

RoHS

Accessory

Mounting Flanges GN 784.1

On request

Clamping with hand knob DIN 6335

Technical drawing

GN 784 Aluminum Swivel Ball Joint sketch

Hide technical drawing

Part Options / Table

Type

A	Ball with internal thread
B	Ball with external thread

Identification no.

1	Clamping with adjustable lever
2	Clamping with set screw with hex socket

Part Number	d₁	d₂* Type A Metric thread	r₁ Type A	d₃* Type A Metric thread	Inch Thread	r₂ Type A	d₄ Type B Metric thread	Inch Thread	r₁ Type B	l₁ Type B

784-23-M5-B-1-ELS	0.91	-	-	-	-	-	M 5	-	0.68	0.31
784-23-M6-B-1-ELS	0.91	-	-	-	-	-	M 6	1/4 (= 1/4-20)	0.68	0.39
784-23-1/4-B-1-ELS	0.91	-	-	-	-	-	-	1/4 (= 1/4-20)	0.68	0.39
784-31-M6-B-1-ELS	1.22	-	-	-	-	-	M 6	1/4 (= 1/4-20)	0.85	0.39
784-31-1/4-B-1-ELS	1.22	-	-	-	-	-	-	1/4 (= 1/4-20)	0.85	0.39
784-31-M8-B-1-ELS	1.22	-	-	-	-	-	M 8	-	0.85	0.47
784-39-M6-B-1-ELS	1.54	-	-	-	-	-	M 6	-	1.00	0.39
784-39-M8-B-1-ELS	1.54	-	-	-	-	-	M 8	3/8 (= 3/8-16)	1.00	0.47
784-39-3/8-B-1-ELS	1.54	-	-	-	-	-	-	3/8 (= 3/8-16)	1.00	0.47
784-49-M8-B-1-ELS	1.93	-	-	-	-	-	M 8	3/8 (= 3/8-16)	1.21	0.47
784-49-3/8-B-1-ELS	1.93	-	-	-	-	-	-	3/8 (= 3/8-16)	1.21	0.47
784-49-M10-B-1-ELS	1.93	-	-	-	-	-	M 10	-	1.21	0.59

Part Number	d₁	d₂* Type A Metric thread	r₁ Type A	d₃* Type A Metric thread	Inch Thread	r₂ Type A	d₄ Type B Metric thread	Inch Thread	r₁ Type B	l₁ Type B

784-23-M5-B-2-ELS	0.91	-	-	-	-	-	M 5	-	0.68	0.31
784-23-M6-B-2-ELS	0.91	-	-	-	-	-	M 6	1/4 (= 1/4-20)	0.68	0.39
784-23-1/4-B-2-ELS	0.91	-	-	-	-	-	-	1/4 (= 1/4-20)	0.68	0.39
784-31-M6-B-2-ELS	1.22	-	-	-	-	-	M 6	1/4 (= 1/4-20)	0.85	0.39
784-31-1/4-B-2-ELS	1.22	-	-	-	-	-	-	1/4 (= 1/4-20)	0.85	0.39
784-31-M8-B-2-ELS	1.22	-	-	-	-	-	M 8	-	0.85	0.47
784-39-M6-B-2-ELS	1.54	-	-	-	-	-	M 6	-	1.00	0.39
784-39-M8-B-2-ELS	1.54	-	-	-	-	-	M 8	3/8 (= 3/8-16)	1.00	0.47
784-39-3/8-B-2-ELS	1.54	-	-	-	-	-	-	3/8 (= 3/8-16)	1.00	0.47
784-49-M8-B-2-ELS	1.93	-	-	-	-	-	M 8	3/8 (= 3/8-16)	1.21	0.47
784-49-3/8-B-2-ELS	1.93	-	-	-	-	-	-	3/8 (= 3/8-16)	1.21	0.47
784-49-M10-B-2-ELS	1.93	-	-	-	-	-	M 10	-	1.21	0.59

Part Number	d₁	d₂* Type A Metric thread	r₁ Type A	d₃* Type A Metric thread	Inch Thread	r₂ Type A	d₄ Type B Metric thread	Inch Thread	r₁ Type B	l₁ Type B

784-23-M4-A-1-ELS	0.91	M 4	0.68	-	-	0.98	-	-	-	-
784-23-M5-A-1-ELS	0.91	-	0.68	M 5	-	0.98	-	-	-	-
784-23-1/4-A-1-ELS	0.91	-	-	-	1/4 (= 1/4-20)	0.98	-	-	-	-
784-31-M5-A-1-ELS	1.22	M 5	0.85	-	1/4 (= 1/4-20)	1.28	-	-	-	-
784-31-M6-A-1-ELS	1.22	-	0.85	M 6	1/4 (= 1/4-20)	1.28	-	-	-	-
784-31-1/4-A-1-ELS	1.22	-	0.85	-	1/4 (= 1/4-20)	1.28	-	-	-	-
784-39-M5-A-1-ELS	1.54	M 5	1.00	-	-	1.43	-	-	-	-
784-39-M6-A-1-ELS	1.54	-	1.00	M 6	-	1.43	-	-	-	-
784-39-M8-A-1-ELS	1.54	-	-	M 8	3/8 (= 3/8-16)	1.59	-	-	-	-
784-39-3/8-A-1-ELS	1.54	-	-	-	3/8 (= 3/8-16)	1.59	-	-	-	-
784-49-M8-A-1-ELS	1.93	M 8	1.21	-	3/8 (= 3/8-16)	1.76	-	-	-	-
784-49-3/8-A-1-ELS	1.93	-	1.21	-	3/8 (= 3/8-16)	1.76	-	-	-	-
784-49-M10-A-1-ELS	1.93	-	-	M 10	-	2.04	-	-	-	-

Part Number	d₁	d₂* Type A Metric thread	r₁ Type A	d₃* Type A Metric thread	Inch Thread	r₂ Type A	d₄ Type B Metric thread	Inch Thread	r₁ Type B	l₁ Type B

784-23-M4-A-2-ELS	0.91	M 4	0.68	-	-	0.98	-	-	-	-
784-23-M5-A-2-ELS	0.91	-	0.68	M 5	-	0.98	-	-	-	-
784-23-1/4-A-2-ELS	0.91	-	-	-	1/4 (= 1/4-20)	0.98	-	-	-	-
784-31-M5-A-2-ELS	1.22	M 5	0.85	-	1/4 (= 1/4-20)	1.28	-	-	-	-
784-31-M6-A-2-ELS	1.22	-	0.85	M 6	1/4 (= 1/4-20)	1.28	-	-	-	-
784-31-1/4-A-2-ELS	1.22	-	0.85	-	1/4 (= 1/4-20)	1.28	-	-	-	-
784-39-M5-A-2-ELS	1.54	M 5	1.00	-	-	1.43	-	-	-	-
784-39-M6-A-2-ELS	1.54	-	1.00	M 6	-	1.43	-	-	-	-
784-39-M8-A-2-ELS	1.54	-	-	M 8	3/8 (= 3/8-16)	1.59	-	-	-	-
784-39-3/8-A-2-ELS	1.54	-	-	-	3/8 (= 3/8-16)	1.59	-	-	-	-
784-49-M8-A-2-ELS	1.93	M 8	1.21	-	3/8 (= 3/8-16)	1.76	-	-	-	-
784-49-3/8-A-2-ELS	1.93	-	1.21	-	3/8 (= 3/8-16)	1.76	-	-	-	-
784-49-M10-A-2-ELS	1.93	-	-	M 10	-	2.04	-	-	-	-

Show / Hide columns

Metric

Dimensions in: Inch (change to Metric)

d₁	d₂* Type A Metric thread	r₁ Type A	d₃* Type A Metric thread	Inch Thread	r₂ Type A	d₄ Type B Metric thread	Inch Thread	r₁ Type B	l₁ Type B

0.91	M 4	0.68	M 5	-	0.98	M 5	-	0.68	0.31
0.91	-	-	-	1/4 (= 1/4-20)	0.98	M 6	1/4 (= 1/4-20)	0.68	0.39
1.22	M 5	0.85	M 6	1/4 (= 1/4-20)	1.28	M 6	1/4 (= 1/4-20)	0.85	0.39
1.22	-	-	-	-	1.28	M 8	-	0.85	0.47
1.54	M 5	1.00	M 6	-	1.43	M 6	-	1.00	0.39
1.54	-	-	M 8	3/8 (= 3/8-16)	1.59	M 8	3/8 (= 3/8-16)	1.00	0.47
1.93	M 8	1.21	-	3/8 (= 3/8-16)	1.76	M 8	3/8 (= 3/8-16)	1.21	0.47
1.93	-	-	M 10	-	2.04	M 10	-	1.21	0.59

Show / Hide columns

Dimensions in: Inch (change to Metric)

d₁	d₅*	d₆	d₇	d₈	h₁	h₂	h₃	k	l₂	m	A/F₁	A/F₂	Recommended tightening torque of the clamping (Identification no.) in Nm ≈	Resulting stop torque on the ball in Nm ≈

0.91	M 5	0.55	0.43	0.10	1.05	0.85	0.42	1.26	0.87	0.28	0.35	0.10	1.5	4.5
0.91	M 5	0.55	0.43	0.10	1.05	0.85	0.42	1.26	0.87	0.28	0.35	0.10	1.5	4.5
1.22	M 6	0.71	0.55	0.14	1.40	1.17	0.59	1.42	0.87	0.35	0.47	0.12	2.5	6.5
1.22	M 6	0.71	0.55	0.14	1.40	1.17	0.59	1.42	0.87	0.35	0.47	0.12	2.5	6.5
1.54	M 8	0.94	0.59	0.18	1.77	1.46	0.74	1.73	1.18	0.47	0.51	0.16	4	16
1.54	M 8	0.94	0.59	0.18	1.77	1.46	0.74	1.73	1.18	0.47	0.51	0.16	4	16
1.93	M 8	1.10	0.77	0.18	2.20	1.81	0.94	1.93	1.18	0.63	0.67	0.16	4	20
1.93	M 8	1.10	0.77	0.18	2.20	1.81	0.94	1.93	1.18	0.63	0.67	0.16	4	20

* The usable thread depth for d₂ / d₃ / d₅ is 1.5 x the thread diameter for metric threads and 1.2 x the thread diameter for inch based threads.

Build & Price

3D Product Configurator

Selected Part

Part Number

Total US Dollars (net)

$60.56

Call / Email for Delivery Time

Quantity

Please note our quantity discounts (US Dollars).

Min	Max	Price
1	49	$60.56
50	99	$55.51
100	249	$50.47
≥ 250		$45.42

Prop 65: Not compliant

WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov

RoHS: Compliant

This article is RoHS-compliant in application of Annex III., which means it complies with EU Directive 2011/65/EU, including extension (2015/863/EU), for restricting the use of certain hazardous substances in electrical and electronic devices. The Directive regulates the use of hazardous substances in devices and components. The implementation in national law is summarily described with RoHS(Restriction of (the use of certain) hazardous substances)).

Weight: 0.065 lbs

If weight is not listed, please contact our Sales Department for additional information regarding weight.
Phone: 800-877-8351

All Prices are in US Dollars. Taxes Not Included.

CAD Download

Other Data Formats

About CAD Downloads

Save as Favorites

Need Help?

Our service team is available from Monday to Friday between 7:30 AM and 5:00 PM Central Time: 800-877-8351

Special Requests | Contact our sales team

GN 784 Swivel Ball Joint Aluminum

Photo

Product description

Information

Specification

Accessory

On request

Technical drawing

Part Options / Table

Type

Identification no.

Type: B - Ball with external thread
Identification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal thread
Identification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: B - Ball with external thread
Identification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal thread
Identification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal thread
Identification no.: 2 - Clamping with set screw with hex socket

Metric

Build & Price

Selected Part

CAD Download

CAD data

Login

Email CAD File

Need Help?

This could also be interesting...

GN 784 Swivel Ball Joint Aluminum

Photo

Product description

Information

Specification

Accessory

On request

Technical drawing

Part Options / Table

Type

Identification no.

Type: B - Ball with external threadIdentification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external threadIdentification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal threadIdentification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal threadIdentification no.: 2 - Clamping with set screw with hex socket

Type: B - Ball with external threadIdentification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external threadIdentification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal threadIdentification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal threadIdentification no.: 2 - Clamping with set screw with hex socket

Metric

Build & Price

Selected Part

CAD Download

CAD data

Login

Email CAD File

Need Help?

This could also be interesting...

Type: B - Ball with external thread
Identification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal thread
Identification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: B - Ball with external thread
Identification no.: 1 - Clamping with adjustable lever

Type: B - Ball with external thread
Identification no.: 2 - Clamping with set screw with hex socket

Type: A - Ball with internal thread
Identification no.: 1 - Clamping with adjustable lever

Type: A - Ball with internal thread
Identification no.: 2 - Clamping with set screw with hex socket